Two sinks can drain into one line. Sharing one trap is a different question, and double sink vanity plumbing turns on how far apart the two sinks sit. Section P3201.6 of the 2018 Tennessee residential code text says each fixture gets its own trap.
One of its exceptions fits a double vanity: a single trap may serve two side-by-side bathroom sinks in the same room on a continuous waste, and only when the trapped outlets are not more than 30 inches apart.
That matters early. The drains, traps and vent go in before the wall is closed, and the building department can flag an arrangement the code text doesn’t allow. Finding that out after the vanity and countertop are set and the wall is painted means opening finished work. So settle the spacing with your remodeler while it’s still a drawing.
Double Sink Vanity Plumbing: Can Two Sinks Share a Trap?
Yes, but it’s a narrow case. The code text’s starting point is a trap for each plumbing fixture. The exception is strict: two bathroom sinks, side by side, in the same room, joined above one trap, with their trapped outlets not more than 30 inches apart. Miss any part of that and each sink gets its own trap.
A trap is the curved section of pipe under a sink that holds a little water. A continuous waste is one drain line that joins the two sinks above a single shared trap. Lavatory is the code’s word for a bathroom sink, and bathroom sinks sit on the short list of like fixtures the exception covers.
P3201.6 asks for all of it at once: like fixtures, next to each other, in the same room, on that continuous waste, and inside the 30 inches. Meeting part of that list isn’t enough.
You can read P3201.6 yourself in the traps chapter of the 2018 Tennessee Residential Code, as published by a code-publishing site. Which code, which edition and which amendments apply at your address is the local building department’s call, so it’s worth asking the remodeler to confirm that for your project.
Why Does Sink Spacing Decide the Plumbing?
Because the gap between the two drains is the test. One shared trap is only on the table when the trapped outlets land not more than 30 inches apart. Spread the sinks out for elbow room at the counter, and you’ve moved the drains apart with them. Then the code text answers with a trap at each sink.
Guthrie’s post on whether your bathroom has room for a double vanity cites a planning guideline that puts two sink centerlines at least 36 inches apart. That spacing is a planning guideline for the counter, not a plumbing rule. Still, it decides where the basins land, and the basins decide where the drains go.
The arithmetic is quick. Give two basins centered drains and centerlines 36 inches apart, and the drains end up 36 inches apart too. That’s past the 30 inches P3201.6 allows for one shared trap, so the code text’s answer for that layout is a trap at each sink.
Not every double vanity is drawn that way, and the drains aren’t always centered under the basins. But Guthrie’s post lands in the same place from the design side: a second basin asks for a second drain.
Can Two Sinks Still Use One Drain Line and One Vent?
Yes. Two trapped sinks can join one drain line inside the wall, and the code text lets a single vent serve both. A vent lets the drain take in air, so the water stays put in the trap. Two traps don’t have to mean two vents.
P3107.1 in the vents chapter of the same code text permits an individual vent to serve two traps or trapped fixtures as a common vent, as long as they’re on the same floor level. P3107.2 handles where that vent ties in: where the two fixture drains join at the same level, the vent connects at that junction or downstream of it.
The plumber and the building department decide the method. Your part is smaller than that. Know which arrangement the plan uses and why, so the drawing and the cabinet match what goes in the wall.
Settle the Plumbing Before the Wall and Cabinet Are Finished
The drains, traps and vent go in while the wall is open. The vanity and countertop come later, and so does the paint. If the drain arrangement has to change after all of that, finished work comes apart to reach it. That’s why sink spacing belongs on the drawing before anything is ordered.
Guthrie’s post on choosing a furniture-style vanity or built-in storage adds one honest caveat: the drain and supply lines eat into the top drawer of any vanity. With two sinks, each basin claims part of that drawer run. So where the drains come through the wall shapes the drawers you end up with.
Here’s what to bring to your remodeler:
- How far apart will the two sinks sit?
- Does that spacing allow one shared trap, or does each sink need its own?
- Where do the two drains meet, and how is that point vented?
- Are the drain and vent already in the wall reused, or do they move?
- How do the cabinet drawers work around the plumbing?
- When does the local building department look at the work?
Frequently Asked Questions About Double Sink Vanity Plumbing
Can I replace a single vanity with a double vanity on the same drain?
The code text lets two sinks drain into one line, so the second basin doesn’t have to find its own path. Whether the pair can share one trap still comes back to the 30 inches in P3201.6. How the drain and vent already in the wall get reused or moved is the plumber’s call, so ask your remodeler what the plan does with them.
Does each sink in a double vanity need its own vent?
Not by itself. P3107.1 permits an individual vent to serve two traps or trapped fixtures as a common vent when they’re on the same floor level. The plumber picks the method and the building department checks the work, so ask which arrangement your plan uses.
What is a continuous waste?
It’s one drain line that joins two sinks above a single shared trap. P3201.6 allows it only for adjacent like fixtures in the same room, with the trapped outlets not more than 30 inches apart. Spread the sinks wider and the layout falls outside that exception.
Will the plumbing take up drawer space in a double vanity?
Some of it, yes. Guthrie’s post on furniture-style vanities notes that the drain and supply lines eat into the top drawer of any vanity. With two sinks, each basin claims a share of that space, so it helps to settle the drain layout and the drawer plan together.
Can Guthrie help me plan a double vanity?
Yes. The design team can help you plan every detail, from spacious showers to custom vanities and elegant finishes. You can visit the Pleasant View showroom to see materials in person, or schedule a consultation to get started.
Plan the Two Sinks and Their Drains Together
At Guthrie’s Pleasant View showroom, you can see materials in person, from cabinetry and countertops to plumbing fixtures.
In practice, double sink vanity plumbing is easiest to get right when the sink spacing and the drains are settled on the same drawing. Start with how far apart the basins sit. Everything else in the wall follows from that one line.
A double vanity touches the design and the wall behind it at once. Bring it up early in bathroom remodeling planning, while the layout is still easy to move.
Ready to put the two sinks on paper? You can talk with Guthrie’s design team about your double vanity and settle the drains before the wall closes.